Back to Blog
Gitup git2 forum7/26/2023 ![]() ![]() First turn on the RAW option in the Photo mode settings. ![]() In Wi-Fi client mode, you'll need to check the IP address displayed on the screen (toggle the network information display by pressing the settings button or the mode button). GitUp Thanks to the DashCamTalk member the-force who helped us to provide this tool and script. Simply choose "Open network stream" and type rtsp:// followed by the camera's IP address. New from GitUp based on Novatek NTK96660 chip with a 16 megapixel Sony Exmor IMX206. On Android, you can use VLC Media Player, available in the Play Store. To view the stream, all you need is a video player capable of opening an RTSP stream. The camera serves up a video feed via RTSP whenever it is connected to WiFi (client mode or AP mode). So this Gist aims to be an unofficial manual for the Git2, and it may be applicable to other GitUp cameras. I had to read 3 forum posts to even figure out how to connect it to a wifi network. As always, if I (or anyone else) finds something, Gitup will take care of it and release a firmware update to take care of it. The form factor has remained the same like on the. The technical platform has also been revamped and it's now based on the new and powerful NTKNTK96660 Novatek chipset. As we were expecting from the Git1 then new Git2 also uses a top quality back-illuminated 16 Megapixel Sony CMOS sensor. ![]() I love my Git2P camera, but I am very disappointed in the unprofessional forum-style support available for even basic functions on the cameras. The new Git2 made by the GitUp has been just released. I decided I did not really want to mess with it any longer, because things seemed kind of flaky and unrealiable - but that was obviously just my experience - I gave up after how easy the gopro worked.Unofficial Manual for GitUp Git2/Git2P Action Cameras ![]() I did not end up liking my setup though, atleast not once I got my gopro, so I returned the Git2. They have the free designs cataloged and the websites software does all the 3D printing calculations automatically (even lets you know if the part will not print correctly) and you do not have to get into all the nitty gritty of 3D printing stuff. The parts turned out really well and I got um relatively cheap because I ordered several parts at the same time all with the same base specs (color, fill-ratio, etc.) so I was only charge one $10 setup fee (the parts themselves cost anywhere from $1.50 - $6 depending on what I was buying and how many I was ordering. Because I really like to photograph with the Git2 the blurring annoys me. The 3D printed parts are available and i purchased from "", their 3D Co-OP-like printing service. The problem is: If not all Edges blurred and only one side of the image the lens isn't perfectly aligned and decentered. The stock solo gimbal HDMI connector works on this camera after you cut away a bit of the plastic underneath the connector - careful not to slice into the rubber covering the HDMI cable as I did, nearly slicing the wire, making my backup gimbal useless. The gimbal functions as smooth as it did with a GoPro. The fact that the Git2P weighs 23grams less than the GoPro Hero 4 Black helps. I was worried the gimbal would have a problem with the new camera sitting a quarter of an inch forward but it was not a problem. A small amount of trimming of plastic corner under the HDMI cable solved this problem. Sensor: Whereas Git2 uses a 16MP Sony IMX206 sensor (same as in YI Action Camera), both new Git2P models hold a 16 MP Panasonic MN34120PA sensor. Be careful, both cameras bear the same name Git2Pindicates the new Panasonic sensor being used. The HDMI cable was a couple of mm to short to plug into the camera. I was following a thread on the Git2 on the RC forums and found that some people were claiming that the SJCAM and Gitup batteries were the same. GitUp released two new versions of Git2: the Git2P. Velcro is simple and secure plus it makes it easy to change cameras. I use a Velcro strap to hold the camera in place. Feiyu Mini3D with GitUp Git2 Camera - RC Groups Classifieds FPV Equipment (FS/W) Sold Feiyu Mini3D with GitUp Git2 Camera Thread Tools This thread is privately moderated by Marc Dornan, who may elect to delete unwanted replies. Then I carefully cut off the rounded tab, on the left side, that was used to hold a GoPro, but was now in the way. Since the GIT2P has to sit in front of the connector, I made a quarter inch thick pad for the camera to rest against (see photo), using the black dense foam that came with the gimbal. I did not want to remove it, because I still want to be able to use it with a GoPro. The first problem I had to deal with was the connector that plugs into the back of a GoPro. Use of this camera required some modifications to the SOLO gimbal, but I made sure that I can still use a GoPro if I want. ![]()
0 Comments
Read More
Leave a Reply. |